Kitchen Plumbing for Remodels in Niles, IL
Kitchen plumbing during a remodel can be straightforward—like swapping out a faucet, connecting a garbage disposal, or hooking up a dishwasher—or much more involved if you’re relocating the sink, adding a gas line for a new range, installing a pot filler, or putting in a prep sink. The size of the job affects the cost, how long it takes, and whether permits are needed. Whatever your needs, our team is ready to tackle it.
Here’s a quick tip from me: have the plumber come in before the cabinets get set. If you’re moving your sink, the drain and vent lines have to be accessible, usually before the subfloor is fully covered. Running a gas line for a new range or island cooktop is another job that needs to happen before cabinetry. Pot filler faucets require opening up the wall behind the stove, so it’s better done before tile and backsplash go in. Getting us on your schedule early helps avoid costly delays in your remodeling timeline.
Besides remodels, we also handle kitchen plumbing repairs and upgrades: replacing faucets, servicing garbage disposals, hooking up dishwashers or refrigerator water lines. Remodeling is also a good time to check if your water heater can keep up with increased demand and clear any slow drains before the new cabinets arrive. Give us a call at 224-537-0248 for any kitchen plumbing needs.
Our Kitchen Plumbing Services
Sink and Faucet Installation
We install all types of kitchen sinks: undermount (careful countertop coordination needed), drop-in, farmhouse/apron front, single or double bowl, and prep sinks. Our installation covers setting up the drain basket, strainer, P-trap, and connecting supply lines. We always use braided stainless steel supply lines instead of older plastic ones to prevent leaks.
We also handle faucet installation—whether it’s a single-hole, triple-hole, or deck-mounted faucet with plate. Before finishing, we pressure-test all connections. Moving a sink to a new location is a bigger job involving drain and vent rerouting, which we perform with the proper permits and inspections.
Connecting Dishwashers and Appliances
Dishwasher hookups include connecting the hot water supply, routing the drain hose with a proper high loop or air gap to avoid backflow, and checking electrical requirements (we work with your electrician on that). For refrigerators with ice makers and water dispensers, we run dedicated cold water lines using copper or stainless steel, complete with accessible shutoff valves behind the fridge.
We also install instant hot water taps, under-sink water filters, and reverse osmosis systems. For RO units, we install the specialized faucet, connect supply and waste lines, and help you maintain filter cartridges. Call us at 224-537-0248 for any appliance plumbing in your kitchen.
Gas Line Installation for Kitchen Appliances
Thinking about switching to gas or adding a gas cooktop to an island? We size the gas pipe correctly to handle your appliance’s BTU demand, run the gas line from the closest supply, install the shutoff valve, connect to the appliance with approved flexible connectors, and pressure-test everything for safety. We also take care of all permits and inspections.
Important: gas line work for new locations like islands must happen before cabinets go in. Running gas lines afterward is tricky and disruptive. Coordinate early with your general contractor and us to keep your project on track.
Pot Filler Faucet Installation
A pot filler sits over your cooktop, letting you fill pots right at the stove without hauling water across the kitchen. It needs a cold water line roughed in inside the wall about 56 to 60 inches above the floor and roughly 4 inches off center from the range. Installing one is much easier during a remodel when walls are open, but we can handle finished kitchen installations with minimal wall repair. Call us at 224-537-0248 to discuss your setup.
Island Sink Drain and Vent Solutions
Installing a sink on a kitchen island is trickier because the drain can’t connect to a vent stack in the wall. Instead, island sinks need an island loop vent or an air admittance valve (AAV), depending on local code. Running hot and cold supply lines to the island is straightforward, but routing the drain and vent pipes through the floor and subfloor takes careful planning. We’ve installed plenty of island sinks and can advise on the best venting solution for your home. Contact us before finalizing your design.
Kitchen Plumbing Checklist
- Remove and install kitchen sinks (undermount, farmhouse, drop-in)
- Install faucets of all types and configurations
- Install or replace garbage disposals
- Connect dishwasher water and drain lines
- Run water line for refrigerator ice makers
- Install gas lines for ranges, cooktops, and ovens
- Rough-in and install pot filler faucets
- Set up under-sink water filtration and RO systems
- Island sink drain and vent installation
- Replace old shutoff valves with modern ball valves
- Install prep or bar sinks in pantry or island areas
Timing Tips for Kitchen Plumbing
- Confirm sink location pre-demo: Sink relocation is the priciest plumbing change—lock in placement before ordering cabinets
- Do gas rough-in early: Gas lines to islands or new appliance locations must be completed before cabinet installation
- Pot filler prep before backsplash: Opening the wall is simpler prior to tile installation
- Upgrade shutoff valves while exposed: Replace unreliable gate valves with ball valves during remodel plumbing work
- Fridge water line first: Running refrigerator water lines is easier before countertops are installed
Frequently Asked Questions About Kitchen Plumbing
Yes, but it’s a more involved job because island sinks require special venting, usually an island loop vent or an air admittance valve (AAV). Running the water supply is straightforward, but the drain and vent pipes must be routed through the floor carefully. We’ve installed many island sinks—give us a call at 224-537-0248 to talk through your plans before you finalize your kitchen layout.
For simple replacements like swapping out a faucet, garbage disposal, or dishwasher hookup in the same location, permits usually aren’t needed. But any work involving rerouting drain or supply lines, new gas lines, or changing the kitchen’s plumbing layout will require a permit. We handle all the paperwork and inspections to keep your project compliant.
Definitely. Installing gas lines is safer and easier during a remodel when walls are open. We size the line to your appliance’s specs, run it from the gas meter or existing line, install shutoffs, test for leaks, and get all required permits. Schedule your gas rough-in before the cabinetry goes in to avoid costly rework.
Yes, we collaborate closely with general contractors and designers as the plumbing subcontractor on kitchen projects. We coordinate our rough-in and finish work with your GC’s schedule and manage permit processes. Reach out at 224-537-0248 to get us involved early.